FSDreamTeam forum
Products Support => GSX Support FSX/P3D => GSX Sharing area - Airplane Configs => Topic started by: Ankh on April 07, 2019, 02:17:10 pm
-
Hi all, below you find the configs for the VirtualCol A220-100 and A220-300. Due to the basic model, it has some limitations.
- Exit 3 opens both back doors and the front right door at once. No chance to change this with my knowledge.
- usually, when served with a jetway, there is no stairs on the back left door. But unless you configured the airport position as such, it will have one. Otherwise, boarding via stairs would be only via front door. Maybe I will remove the second stair for the -100 variant, as this can be boarded via a single stair only.
Here we go:
A220-100:
[aircraft]
nosegear = 11.84
refueling = 1
battery = 1
iscargo = 0
trafficcones = 1
preferredexit = 0
wingrootpos = 1.75 -3.60 0.00
wingtippos = 17.54 -8.77 0.00
fuelpos = 9.75 -2.76 0.47
waterpos = 0.00 -13.25 -0.15
lavatorypos = 0.00 -13.25 -0.15
engine1pos = -5.67 3.09 -1.64
engine2pos = 5.67 3.09 -1.64
engine3pos = 0.00 0.00 0.00
engine4pos = 0.00 0.00 0.00
[exit1]
pos = -1.81 9.84 -0.08 0.00
code = 1
name = Exit 1
embeddedStair = 0
[exit2]
remove = 1
[exit3]
remove = 1
[exit4]
pos = -1.75 -11.04 0.04 -9.00
code = 3
name = Exit 3
embeddedStair = 0
[service1]
pos = 1.81 10.34 -0.07 -0.00
code = 3
name = Exit 1
embeddedStair = 0
[service2]
pos = 1.69 -11.16 -0.06 8.00
code = 3
name = Exit 1
embeddedStair = 0
[cargo1]
pos = 0.92 7.93 -1.14 0.00
code = 2
name = Exit 2
embeddedStair = 0
uldcode = BELT
[cargo2]
pos = 1.00 -6.52 -1.16 -0.00
code = 2
name = Exit 2
embeddedStair = 0
uldcode = BELT
[cargomain]
remove = 1
A220-300
[aircraft]
nosegear = 14.02
refueling = 1
battery = 1
iscargo = 0
trafficcones = 1
preferredexit = 0
wingrootpos = 1.75 -3.60 0.00
wingtippos = 17.54 -8.77 0.00
fuelpos = 9.25 -2.76 0.47
waterpos = 0.00 -14.25 -0.16
lavatorypos = 0.00 -14.50 -0.16
engine1pos = -5.49 2.95 -1.64
engine2pos = 5.49 2.95 -1.63
engine3pos = 0.00 0.00 0.00
engine4pos = 0.00 0.00 0.00
[exit1]
pos = -1.59 12.04 -0.06 3.00
code = 1
name = Exit 1
embeddedStair = 0
[exit2]
remove = 1
[exit3]
remove = 1
[exit4]
pos = -1.57 -12.79 0.00 -9.00
code = 3
name = Exit 3
embeddedStair = 0
[service1]
pos = 1.62 12.48 -0.05 -2.00
code = 3
name = Exit 3
embeddedStair = 0
[service2]
pos = 1.72 -12.79 0.00 4.00
code = 3
name = Exit 3
embeddedStair = 0
[cargo1]
pos = 0.40 10.24 -1.20 1.00
code = 2
name = Exit 2
embeddedStair = 0
uldcode = BELT
[cargo2]
pos = 0.40 -7.94 -1.20 -3.00
code = 2
name = Exit 2
embeddedStair = 0
uldcode = BELT
[cargomain]
remove = 1