FSDreamTeam forum

General Category => General Discussion => Topic started by: Zigarten on May 31, 2015, 05:15:50 am

Title: Feedback on installed YVR scenery
Post by: Zigarten on May 31, 2015, 05:15:50 am

Experiencing some stutters in the Lower Mainland. Here is a list of what I installed, can anyone tell me the worst culprit is?  

Traffic360
BC Ferries
ORBX Libraries
PNG Holgermesh <----should this be at a higher number?
All my Orbx all mishmash from 7 through  34  does it matter that mesh is mixed with city and Yosemite regional
the FSDT CYVR
BeaverX-Pier39 BeaverPier39
Vanplus v3\Vanplus_Higher_priority
"                "          Lower_priority     <---------- ok that I have both? Was I suppose to just pick one?
PNG Bush Flying
PNG Bush PNG Mesh   <---------- conflict with Holger? This is the raw grit Papaua New Guinea stuff.

What are the ideal settings in FSX AI boats etc.

Thank you for any advice!
Gord

Title: Re: Feedback on installed YVR scenery
Post by: Bruce Hamilton on May 31, 2015, 07:55:30 pm

CYVR should be above your ORBX entries, it sits on the area covered by Pacific Northwest.

Title: Re: Feedback on installed YVR scenery
Post by: virtuali on June 01, 2015, 10:33:04 am

Just having "some stutters", with all that stuff installed ( yes, FSDT CYVR should be on top of everything, and you will probably need to remove the CYVR AFCAD from Traffic360 too ), it's a *very* good result, you should be happy your FSX doesn't OOM.

Title: Re: Feedback on installed YVR scenery
Post by: Zigarten on June 01, 2015, 04:53:29 pm

Quote from: virtuali on June 01, 2015, 10:33:04 am

Just having "some stutters", with all that stuff installed ( yes, FSDT CYVR should be on top of everything, and you will probably need to remove the CYVR AFCAD from Traffic360 too ), it's a *very* good result, you should be happy your FSX doesn't OOM.

So to make sure I never have any OOM's, what would you suggest I should do? I could randomly remove things but I thought I'd ask for some feedback.

Title: Re: Feedback on installed YVR scenery
Post by: Bruce Hamilton on June 01, 2015, 05:18:44 pm

You can't totally prevent OOM, it's pretty much inherent in both FSX and P3D, and will be as long as they're 32 bit programs.  If we ever get to 64 bit and can use more memory, you would be OOM less often.

Title: Re: Feedback on installed YVR scenery
Post by: Zigarten on June 11, 2015, 03:57:53 am

I don't beleive I've evered oom'd  ;D

Title: Re: Feedback on installed YVR scenery
Post by: Bruce Hamilton on June 11, 2015, 08:02:14 pm

Lucky you.   ;D

Title: Re: Feedback on installed YVR scenery
Post by: pcubine on June 12, 2015, 05:26:06 pm

Quote from: Zigarten on June 11, 2015, 03:57:53 am

I don't beleive I've evered oom'd 

What are you flying into CYVR?

Title: Re: Feedback on installed YVR scenery
Post by: Zigarten on June 12, 2015, 06:18:23 pm

Like A/C? A mixture, I use Air Hauler to get off my a** and actually go places, great motivator, especially when you owe the bank $22,000,000 for a used 737 and you just pranged a Metroliner into the side of a mountain ::).

Caravan's too. Oh and a Carenad Twin Otter

Gord

Title: Re: Feedback on installed YVR scenery
Post by: Zigarten on December 29, 2015, 07:02:06 pm

Quote from: Bruce Hamilton on June 11, 2015, 08:02:14 pm

Lucky you.   ;D

My luck has run out Bruce. After adding Orbx Global, Vectors & Land-class flying the Lionheart Lear over "default" area I got it.  :-\